Motion Pro Hydraulic One Way Bleeder Valve

  • VendorMotion Pro

Description

Make Brake Bleeding a One-Person Job

The Motion Pro Hydraulic Brake Bleeder uses an internal one-way check valve to let old brake fluid and trapped air flow out while helping prevent air from being drawn back into the system. Its compact billet-aluminum body and clear tubing make routine motorcycle brake maintenance cleaner, easier to monitor and manageable by one person.

Key Features

  • Motion Pro part number 08-0143
  • Billet-aluminum valve body with an internal one-way check valve
  • Helps prevent air from re-entering the hydraulic system during bleeding
  • Clear 3/16-inch inside-diameter tubing lets you watch fluid flow and air bubbles
  • Flow-direction arrow on the valve body aids correct setup
  • Compact design works with motorcycle and ATV hydraulic brake systems
  • Includes bleeder valve, clear tubing, hose clamp and instructions

Basic Use

  1. Fit one clear hose to each end of the tool and connect the inlet hose to the caliper bleeder valve.
  2. Route the outlet hose into a suitable brake-fluid catch container. The arrow should point from the caliper toward the catch container.
  3. Keep the tool vertical and prime it as directed before beginning the bleed process.
  4. Open the bleeder approximately one-half turn, operate the brake lever or pedal and keep the master-cylinder reservoir filled with the manufacturer-recommended fluid.
  5. Continue until the fluid is clean and no air bubbles remain, then tighten the bleeder to the vehicle manufacturer’s specification.

Important: This tool will not remove air from a completely dry hydraulic system. An appropriate wrench is still required to open and close the vehicle’s bleeder screw. Always follow the motorcycle or ATV manufacturer’s service instructions and brake-fluid specification.

Brake fluid caution: Brake fluid can irritate eyes and damage painted surfaces. Wear suitable protection, contain spills and rinse affected painted surfaces immediately with water.

California Proposition 65: This product carries a warning for potential exposure to DEHP. See P65Warnings.ca.gov.

Read more

Motion Pro Hydraulic One Way Bleeder Valve

  • VendorMotion Pro
Product form

$15.99

Make Brake Bleeding a One-Person Job The Motion Pro Hydraulic Brake Bleeder uses an internal one-way check valve to let... Read more

      Free pickup in our shop(s)

      1 in stock

        • Guaranteed secure & safe checkout.

          shop pay

        Estimate Your Delivery Date

        Description

        Make Brake Bleeding a One-Person Job

        The Motion Pro Hydraulic Brake Bleeder uses an internal one-way check valve to let old brake fluid and trapped air flow out while helping prevent air from being drawn back into the system. Its compact billet-aluminum body and clear tubing make routine motorcycle brake maintenance cleaner, easier to monitor and manageable by one person.

        Key Features

        • Motion Pro part number 08-0143
        • Billet-aluminum valve body with an internal one-way check valve
        • Helps prevent air from re-entering the hydraulic system during bleeding
        • Clear 3/16-inch inside-diameter tubing lets you watch fluid flow and air bubbles
        • Flow-direction arrow on the valve body aids correct setup
        • Compact design works with motorcycle and ATV hydraulic brake systems
        • Includes bleeder valve, clear tubing, hose clamp and instructions

        Basic Use

        1. Fit one clear hose to each end of the tool and connect the inlet hose to the caliper bleeder valve.
        2. Route the outlet hose into a suitable brake-fluid catch container. The arrow should point from the caliper toward the catch container.
        3. Keep the tool vertical and prime it as directed before beginning the bleed process.
        4. Open the bleeder approximately one-half turn, operate the brake lever or pedal and keep the master-cylinder reservoir filled with the manufacturer-recommended fluid.
        5. Continue until the fluid is clean and no air bubbles remain, then tighten the bleeder to the vehicle manufacturer’s specification.

        Important: This tool will not remove air from a completely dry hydraulic system. An appropriate wrench is still required to open and close the vehicle’s bleeder screw. Always follow the motorcycle or ATV manufacturer’s service instructions and brake-fluid specification.

        Brake fluid caution: Brake fluid can irritate eyes and damage painted surfaces. Wear suitable protection, contain spills and rinse affected painted surfaces immediately with water.

        California Proposition 65: This product carries a warning for potential exposure to DEHP. See P65Warnings.ca.gov.

        Read more

        Recently viewed products

        Footer image

        © 2026 Eagle Leather, Powered by Shopify

          • Amazon
          • American Express
          • Apple Pay
          • Diners Club
          • Discover
          • Google Pay
          • Mastercard
          • PayPal
          • Shop Pay
          • Visa

          Login

          Forgot your password?

          Don't have an account yet?
          Create account