Description
Heat-sealed backing for easy iron-on application.
Features:
Patch Sewing Instructions:
Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.
Identify where you want the patch and outline the area with tailor’s chalk
Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
Position your inside hand so it is resting flat between the lining and outlines area
Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
Finally rest itch the garments lining and your all set
Patch Iron-on Instructions:
Preheat your iron to 325-335 degrees. Do Not Use Steam
Press the area where you want your patch to be for 25 seconds
Position the patch on the garment so that it is positioned where you would like it to be
Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure on the area for 15 seconds
The iron should never come into direct contact with the patch
Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
Turn the garment right side in once more, use your clean lightweight cloth to cover the patch
Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
Let the garment cool completely before wearing
Description
American Flag Reflective Motorcycle Embroidered patch that combines design with reflective material. The white portion of this patch reflects light to keep you visible on the road and anywhere you go. It's a great new twist on some old favorite motorcycle patches. Heat-sealed backing for easy iron-on application.
Patch Sewing Instructions:
Note: Sewing by hand will give you greater control and is easier than trying to use a sewing machine when sewing into leather. Sewing on a patch will leave permanent holes on your jacket to please be careful about placement before you start.
Identify where you want the patch and outline the area with tailor’s chalk
Using a sewing pick, pick open the bottom seam of your garment lining just enough to allow your hand to fit inside the garment
Position your inside hand so it is resting flat between the lining and outlines area
Use your outside had to position the patch, you can lightly spray leather adhesive on the area to hold the patch, however this is not a permanent adhesive
Begin threading your upholstery needle using a strong nylon thread that matches your patch, use your thimble to push the needle through the leather moving from inside the item to the outside
This will allow the knot to be on the inside of the item, then pull the needle through and out with your outside hand and back down through the patch and leather
Continue this pattern all around the patch, keeping stitches close together and to the end of the patch for the most secure attachment
Once you have gotten back to where you started, send the needle through the first stitch, and loop it around a few times to make a finishing knot
Finally restitch the garments lining and your all set
Patch Iron-on Instructions:
Preheat your iron to 325-335 degrees. Do Not Use Steam
Press the area where you want your patch to be for 25 seconds
Position the patch on the garment so that it is positioned where you would like it to be
Place a lightweight cloth over the patch, using a back-and-forth motion with medium pressure ron the area for 15 seconds
The iron should never come into direct contact with the patch
Carefully turn your garment inside out, using the same back and forth motion firmly iron the inside of the item where your patch is for about 1 minute
Turn the garment right side in once more, use your clean lightweight cloth to cover the patch
Iron the edges of the patch through the cloth to ensure they are thoroughly sealed
Let the garment cool completely before wearing
5x3 inches
Sew or iron on
Quality detailed embroidering on heavy canvas
Perfect for clothing or gear and a way to show military appreciation!
Great addition to your collection!
Patch USMC Bulldog
Officially Licensed by the Marine Corps
Approximately 3.25" diameter
Excellent detail and finish
Perfect accent piece to clothing, bags, hats, and more
Iron-On Adhesive - high quality, sturdy, machine washable
Feature:-
Perfect Purchase for a Gift.
Great craftsmanship.
A Must Buy Item.Patch 101st A/B Durable fabric construction. Easy iron-on back. Vibrant sewn and embossed design.
Perfect purchase for a gift
Great craftsmanship
A must buy item
Size: 4 1/8 Inch
Army Para Logo (Camo)Durable fabric construction. Easy iron-on back. Vibrant sewn and embossed design
USN Top Gun Grey
Package Length: 3.5"
Package Width: 1.0"
Package Height: 1.75"
Country of origin: China
This gorgeous PATCH-USN,TOP GUN,GREY (3.5'') has the finest details and highest quality you will find anywhere! PATCH-USN,TOP GUN,GREY (3.5'') is truly remarkable. Product Details: •Condition: Brand New •Item SKU: SS-EAG-PM0187
